MARSTON GLUE INSTANT ADHESIVE

Premium Glue instant adhesive

There is no adhesive which can bond everything. Specific adhesives are necessary for various materials which are matched with them as regards their structural composition and in their viscosity.
MARSTON GLUE instant adhesive by MARSTON-DOMSEL is supplied in practical bottles with droppers and is available in various versions for all kinds of materials.

Economical in use
Precise application possible
High impact resistance
Extremely high tensile strength
High temperature stability
Good water resistance for special types
Bonds in a few seconds
NSF Approval

Areas of application

Electrical and electronics industrie
Engineering
Metalworking
Automotive contruction
Model construction
Furniture industry
Plastic processing
Dentistery
Fingernail bonding
Rubber industry
Lightning industrie
etc.

NEW!!! MD GLUE RAPID SECURE

ULTRA FAST & EXTREMELY TIGHT

METHOXYETHYL CYANOACRYLATE

instant
high adhesion
strenght
multi-substrate
easy to use
transparent
label free
non sensitising
odorless
low blooming
more flexible
dielectrric strenght
also suitable for porous materials

Click here for our MD Glue rapid secure flyer

Marston Premium Glue

MOISTURE RESISTANT

Among other things, MOISTURE RESISTANT is moisture-resistant. Compared with a standard CA adhesive, it features excellent media resistance.

Low viscosity.

Available in:

Item No. bottle 20 g MGL.PM.F20 unit 12

DUPLEX

DUPLEX is characterised by the two different ways of curing – through UV light or humidity. Thus, even non-transparent materials can be transparently bonded free of errors. Excess adhesive can be hardened in 1–2 s. It can also be used as a casting mass.
Medium viscosity

Available in:

HEAT

HEAT is a high-temperature adhesive that can be used in all areas in which high temperatures are required. In this temperature range (up to 150°C), permanently achieving a firm bond is a novelty.
Medium viscosity.

Available in:

Item No. bottle 20 g MGL.PH.F20 unit 12

Marston Glue instant adhesive

MD GLUE XTREME 1

ISEGA certificate / NSF certificate

* Low viscosity (ca. 40 – 60 mPa.s)
* Odorless
* Remains flexible
* Very high adhesive power
* No hazard signs
* temperature resistance from -50 to + 80°C
* curing time handling approx.5-90 sec

available in:
Item No. MGL.X1.ST12 unit 18
Item No. MGL.X1.F25 unit 12

MD GLUE XTREME 2

ISEGA certificate / NSF certificate

* Medium viscosity (ca. 120 – 250 mPa.s)
* Odorless
* Non blooming
* Remains flexible
* Very high adhesive power
* No hazard signs

Temperature resistance from -50 to + 80°C
Curing time handling approx. 5 – 90 seconds

NSF Listed P1 (Reg. No. 151975)

Available in:

MD GLUE XTREME 3

ISEGA certificate / NSF certificate

* High viscosity (ca. 1200 – 1500 mPa.s)
* Odorless
* Non blooming
* Remains flexible
* Very high adhesive power
* No hazard signs

Temperatur resistance von -50 to +80°C
Curing time handling approx. 10 – 120 seconds

NSF Listed P1 (Reg. No. 151977)

Available in:
tem No. MGL.X3.ST12 unit 18
Item No. MGL.X3.F25 unit 12

MD GLUE 100

low viscosity (3-10 mPa.s)

Very fast, capillary action.

free from solvents
extremely fast bonding
easy to use

Temperature resistance from: -50 ° C to +80 ° C
Hand strength: 2 – 10 seconds
Max. Gap filling capacity: 0.05 mm

Available in:
Item No. bottle MGL.100.F10 unit 25 | F20 unit 12
| F50 unit 12 | F500 unit 1

MD GLUE 101.4062

low viscosity (ca. 2-5 mPa.s)

For extremely rapid instant bonding of smooth plastic or rubber surfaces.
Subsequent adjustment is no longer possible. Thin fluid with a capillary action.

Application: universally applicable.
curing time handling: 2 – 5 seconds
temperatur resistance: -50°C to +80°C
gap-filling: 0,05 mm

Available in:
Item No. bottle MGL.101.F10 unit 25 | F20 unit 12
| F50 unit 12 | F500 unit 1

MD GLUE 111.495

NSF certificate

low viscosity (ca. 35-70 mPa.s)

For high-strength bonding of metals and plastic combinations.
Universally applicable.

Application: metal, rubber, plastic, glass, leather
curing time handling:   5 – 15 seconds
temperatur resistance:   -50°C to +80°C
gap-filling:   0,07 mm

NSF Category Code: P1 No. 151977

Available in:
Item No. bottle MGL.111.F10 unit 25 | F20 unit 12
| F50 unit 12 | F500 unit 1|
Smart tube MGL.111.TS4 unit 12

MD GLUE 150.424

NSF certificate

medium viscosity (ca. 50-100 mPa.s)

For universal application with a wide variety of materials.

curing time handling: 8 – 20 seconds
temperatur resistance: -60°C to +80°C
gap-filling: 0,10 mm

NSF Category Code: P1 No. 150265

Available in:
Item No. bottle MGL.150.F10 unit 25 | F20 unit 12
| F50 unit 12 | F500 unit 1

Item No. cartridge 5 g MGL.150.PT5 unit 25
| bottle 20 g / blistercard MGL.150.F20-BK unit 10

MD GLUE 200.435

NSF certificate

medium viscosity (ca. 200-350 mPa.s)

For bonding porous surfaces. Especially suitable for wood, rubber,
ceramics, cork etc.

Application: porous surfaces
curing time handling:   10 – 20 seconds
temperatur resistance:   -50°C to +80°C
gap-filling:   0,15 mm

Available in:
Item No. bottle MGL.200.F10 unit 25 | F20 unit 12
| F50 unit 12 | F500 unit 1

MD GLUE 300.431

NSF certificate

high viscosity (ca. 1200-1500 mPa.s)

For bonding highly porous and uneven surfaces.
Especially suitable for wood, leather etc.

Application: porous surfaces
curing time handling:   10 – 30 seconds
temperatur resistance:   -50°C to +80°C
gap-filling:   0,20 mm

NSF Category Code: P1 No. 150268

Available in:
Item No. bottle MGL.300.F10 unit 25 | F20 unit 12
| F50 unit 12 | F500 unit 1

MD GLUE 310.415

high viscosity (ca. 1200-1700 mPa.s)

For bonding metals, metal/rubber and metal/plastic combinations.
Especially suitable for slightly uneven metal parts.

curing time handling:10 – 30 seconds
temperatur resistance: -60°C to +80°C
gap-filling: 0,30 mm

Available in:
Item No. bottle MGL.310.F10 unit 25 |F20 unit 12 |
F50 unit 12 | F500 unit 1

MD GLUE plus 405

NSF certificate

high viscosity (ca. V 2.500-3.000 mPas)

Six times more impact resistance and ten times more peeling resistance than a conventional CA adhesive. Very high tensile shearing strength (240 kg per square centimetres with steel/steel). Temperature resistance up to +135 °C (with this high load the adhesive still possesses tensile shearing strength of 60 kg/cm² with steel), greater waterproofness, hard to the touch in just 45 seconds (an extraordinary figure for a CA adhesive with a viscosity of approx. 3000 mPa.s)

curing time handling: 20 – 50 seconds
temperatur resistance: -60°C to +135°C
gap-filling: 0,15 mm

NSF Listed P1 (Reg. No. 150267)

Available in:
Item No. bottle MGL.405.F20 unit 12 | F100 unit 12
| F500 unit 1

MD GLUE BS.406

NSF certificate

low viscosity (ca. 3-10 mPa.s)

For bonding rubber, plastic, steel, metals and EPDM. Bonds quickly.

curing time handling: 2 – 10 seconds
temperatur resistance: -50°C to +80°C
gap-filling: 0,05 mm

NSF Listed P1 (Reg. No. 150266)

Available in:
Item No. bottle MGL.BS.F10 unit 25 | F20 unit 12
| F50 unit 12 | F500 unit 1

MD GLUE BS100.401

medium viscosity (ca. 100 mPa.s)

For bonding rubber (EPDM), plastics, steel and metals.
Sticks within 1 – 3 seconds.

curing time handling:   2 – 10 seconds
temperatur resistance:   -60°C to +80°C
gap-filling:   0,07 mm

Available in:
Item No. bottle MGL.BS1.F10 unit 25 | F20 unit 12
| F50 unit 12 | F500 unit 1

MD GLUE BS Special

low viscosity (ca. 15-25 mPa.s)

For bonding rubber, plastic, steel and other metals.

curing time handling:   2 – 10 seconds
temperatur resistance:   -50°C to +80°C
gap-filling:   0,05 mm

Available in:
Item No. bottle MGL.BS-SP.F10 unit 25 | F20 unit 12
| F50 unit 12 | F500 unit 1

MD GLUE EL.4850

mittelviskos (ca. 90-120 mPa.s)

Bleibt elastisch! Biegbar bis 180°, für Gummi und
Gummi-Kunststoff-Kombinationen. Besonders geeignet
für O-Ringe und Gummiteile, die dauernden Bewegungen ausgesetzt sind.

Handfestigkeit: 3 – 10 Sekunden
Temperaturbeständigkeit: -60°C bis +80°C
Spaltfüllvermögen: 0,05 mm

Available in:
Item No. bottle MGL.EL.F10 unit 25 | F20 unit 12
| F50 unit 12 | F500 unit 1

MD GLUE FL.403

medium viscosity (ca. 90-120 mPa.s)

For transparent and translucent plastics. The
bonded location leaves no white edge and does
not effloresce.

Available in:
Item No. bottle MGL.FL.F20 unit 12 | F50 unit 12

MD GLUE GA.460

low viscosity (ca. 30 – 50 mPa.s)

Odourless CA adhesive. Suitable for polystyrene, acrylic glass and transparent materials. Does not effloresce.

curing time handling: 5 – 20 seconds
temperatur resistance: -60°C to +80°C
gap-filling: 0,03 mm

Available in:
Item No. bottle MGL.GA.F20 unit 12 | F50 unit 12

MD GLUE M.493

low viscosity (ca. 10-30 mPa.s)

Methyl-Base.
For rapid bonding of smooth materials, metal/rubber and metal combinations.

curing time handling: 20 – 70 seconds
temperatur resistance: -50°C to +80°C
gap-filling: 0,05 mm

Available in:
Item No. bottle MGL.M.F10 unit 25 | F20 unit 12
| F50 unit 12 | F500 unit 1

MD GLUE M100.496

medium viscosity (ca. 90-120 mPa.s)

Methyl-Base. For bonding metal and plastic combinations.

curing time handling: 5 – 15 seconds
temperatur resistance: -60°C to +80°C
gap-filling: 0,10 mm

Available in:
Item No. bottle MGL.M1.F10 unit 25 | F20 unit 12
| F50 unit 12 | F500 unit 1

MD GLUE G.454 gel

thixotropic (ca. 50.000 mPa.s)

Special instant adhesive in thixotropic form. Does not run, can also be worked on vertical surfaces. Bonding of metal, wood and plastic.

curing time handling: 5 – 60 seconds
temperatur resistance: -60°C to +80°C
gap-filling: 0,50 mm

Available in:
Item No.tube 3 g MGL.G.T3 unit 10 | tube 3 g
/blister card MGL.G.T3-BK unit 12 | tube 20 g MGL.G.T20

MD GLUE SQ.414

medium viscosity (ca. 90-120 mPa.s)

For fast bonding of plastic and rubber.

curing time handling: 3 – 30 seconds
temperatur resistance: -55°C to +80°C
gap-filling: 0,10 mm

Available in:
Item No. bottle MGL.SQ.F10 unit 25 | F20 unit 12
| F50 unit 12 | F500 unit 1

MD GLUE SW4.480

medium viscosity (ca. 500-1.000 mPa.s)

Black impact-resistant instant adhesive.
For bonding rubber and metals.

curing time handling:   5 – 40 seconds
temperatur resistance:   -50°C to +120°C
gap-filling:   0,10 mm

Available in:
Item No. bottle MGL.SW4.F20 unit 12 | F50 unit 12

MD GLUE SW15

high viscosity (ca. 1500 mPa.s)

Black impact-resistant instant adhesive. For bonding rubber and metals.
High temperature resistance up to 120°C. Withstands vibration.

curing time handling: 10 – 30 seconds
temperatur resistance: -60°C to +120°C
gap-filling:

Available in:
Item No. bottle MGL.SW15.F20 unit 12 | F50 unit 12

MD BLUE REMOVER

Removes adhesives from hands, upholstery, plastics and many other materials
(a material test is recommended before use).

Areas of application:

The electrical and electronics industries, lighting industry,
metalworking, automotive construction, model construction,
furniture industry etc.

Available in:
Item No. bottle MGL.MRM.F20 unit 25 | F500 unit 1